Shopping Online at | Price Comparison Site.Download & Streaming : AyamiOoruri29 Favorites : Internet Archive

Looking for:

shell-storm | Shellcodes Database - Quick Links 

Click here to DOWNLOAD

   

 

Statcounter Global Stats - Browser, OS, Search Engine including Mobile Usage Share - Caricato da

  The aim is basically to replicate the Plex Demo concept, what longhorn could have been, if microsoft was more clear, and had their features planned properly. Allows hard drives to monitor their own health and to raise flags if imminent failures were predicted.  

QuickSpecs HP xw Workstation - ethics lesson 1

 

Do not use this product until you have a full knowledge of the equipment, safety information and instructions. CPU E. OV3 E. Thamrin No. Bangalore Branch Taiwan, R. Prestige Emerald, 6th Floor, Municipal No. City Building, Office Tower 1, No. Acesso Jose Sartorelli, KM 2.

Polish Branch Balice ul. Krakowska 50, Poland TEL. Russian Branch St. Petersburg office Piskarevsky pr. Petersburg, Russia TEL. Please forward this Instruction Manual Startup to the end user. Safety Instructions Do not attempt to install, operate, maintain or inspect the product until you have read through this Instruction Manual Startup and appended documents carefully and can use the equipment correctly. Installation, operation, maintenance and inspection must be performed by qualified personnel.

Here, qualified personnel means personnel who meets all the conditions below. Such training may be available at your local Mitsubishi Electric office. Contact your local sales office for schedules and locations. Incorrect handling may cause hazardous Caution conditions, resulting in medium or slight injury, or may cause only material damage.

The Caution level may even lead to a serious consequence according to conditions. Both instruction levels must be followed because these are important to personal safety. Do not run the inverter with the front cover or the wiring cover removed. Otherwise you may access the exposed high voltage terminals or the charging part of the circuitry and get an electric shock. You may accidentally touch the charged inverter circuits and get an electric shock. Any person who is involved in wiring or inspection shall wait for at least 10 minutes after the power supply has been switched OFF and check that there are no residual voltage using a tester or the like.

The capacitor is charged with high voltage for some time after power OFF, and it is dangerous. Earthing grounding must conform to the requirements of national and local safety regulations and electrical code NEC section , IEC class 1 and other applicable standards.

A neutral-point earthed grounded power supply for V class inverter in compliance with EN standard must be used. Otherwise you may get an electric shock or be injured. Otherwise you may get an electric shock.

It is dangerous to change the cooling fan while power is ON. Never touch the motor terminal, etc. Motor terminals holds high-voltage while the motor is running even after the inverter power is turned OFF. Before wiring or inspection, the motor must be confirmed to be stopped. In an application, such as fan and blower, where the motor is driven by the load, a lowvoltage manual motor starter must be connected at the inverter's output side, and wiring and inspection must be performed while the motor starter is open.

Mounting it to or near flammable material may cause a fire. A continuous flow of large current may cause a fire. Otherwise the brake resistor may excessively overheat due to damage of the brake transistor and such, causing a fire. Doing so could cause a fire. If a product is used without any inspection, a burst, breakage, or a fire may occur. Otherwise burst, damage, etc. Touching these devices may cause a burn.

If the product is handled incorrectly, it may cause unexpected fault, an injury, or an electric shock. Failure to do so may lead to injuries. That includes screws and metal fragments or other flammable substance such as oil. Otherwise the inverter may be damaged. Refer to page 3 for details. Halogenbased materials are often included in fumigant, which is used to sterilize or disinfest wooden packages.

When packaging, prevent residual fumigant components from being infiltrated into Mitsubishi products, or use an alternative sterilization or disinfection method heat disinfection, etc.

Sterilization of disinfection of wooden package should also be performed before packaging the product. These devices on the inverter output side may be overheated or burn out. Otherwise the motor will rotate inversely. Before wiring, the PM motor must be confirmed to be stopped. A failure to do so may cause some machines to make unexpected motions.

Resetting inverter fault with the start signal ON restarts the motor suddenly. Connection of any other electrical equipment to the inverter output may damage the equipment.

It must be confirmed that the motor running will not cause any safety problem before performing pre-excitation. Doing so may lead to fault or damage of the product. It is recommended to install both an external thermal and PTC thermistor for overheat protection.

Otherwise the life of the inverter decreases. Otherwise nearby electronic equipment may be affected. Surge voltage attributable to the wiring constants may occur at the motor terminals, deteriorating the insulation of the motor.

Before changing its setting, the performances of the motor and machine must be fully examined. Do not use a synchronous motor, induction motor, or synchronous induction motor. Do not use an induction motor in the PM sensorless vector control settings. It will cause a failure. The cause of the trip must be identified and removed before turning ON the power of the breaker. Never operate the product in this manner.

The cover must be always reinstalled and the instruction in the Instruction Manual must be followed when operating the product. Example FR-A 0. Leave enough clearances and take cooling measures. Avoid places where the inverter is subjected to direct sunlight, high temperature and high humidity. Install the inverter on a nonflammable wall surface. When encasing multiple inverters, install them in parallel as a cooling measure. For replacing the cooling fan of the FR-A K or higher, 30cm of space is necessary in front of the inverter.

Refer to the Instruction Manual Detailed for fan replacement. For the installation at an altitude above 1, m Surrounding Air Temperature is a temperature measured at a measurement position in an enclosure.

Ambient Temperature is a temperature outside an enclosure. When selecting a DC reactor, refer to page 25, and select one suitable for the applicable motor capacity. The function of these terminals can be changed with the input terminal assignment Pr. Refer to page Terminal JOG is also used as the pulse train input terminal. Use Pr. Terminal input specifications can be changed by analog input specification switchover Pr. Terminals 10 and 2 are also used as a PTC input terminal.

Install a thermal relay to prevent overheating and damage of discharging resistors. Refer to the Instruction Manual Detailed. The function of these terminals can be changed with the output terminal assignment Pr.

Not required when calibrating the scale with the operation panel. Also, separate the main circuit cables at the input side from the main circuit cables at the output side. Wire offcuts can cause an alarm, failure or malfunction. Always keep the inverter clean. When drilling mounting holes in an enclosure etc. Incorrect setting may cause a fault, failure or malfunction.

Do not connect anything to these. Phase need not be matched. Never connect the power cable to the U, V, W of the inverter.